Flat Ribbon Kanthal Wire

Great stuff, well impressed with it so far :)


ttp://ego2.pl/en/warsztat/290-tasma-kanthal-d-ribbon.html

0.3 x 0.10mm - 48,9 ohm/m,
0.3 x 0.15mm - 32,6 ohm/m,
0.5 x 0.10mm - 29,4 ohm/m,
0.6 x 0.10mm - 24,5 ohm/m


Comments

  1. Artus4 February 2013 at 15:46

    Got some in over the weekend I really like it

    ReplyDelete
  2. Dave H4 February 2013 at 16:08

    Looks like good stuff. I've got a IGO-L on it's way to me and this might be good in there. I'm guessing you could make a longer coil in a dripper atty, might be good :-)

    ReplyDelete
  3. Unknown4 February 2013 at 16:47

    Looks like some good wire! Would love to try it, but I doubt I could make enough wraps to hit 1.8Ω with it inside this tiny vision eternity atty haha!

    ReplyDelete
  4. Sarah XXX4 February 2013 at 17:09

    "Helloooo" you do make me laugh!

    But :( cos not had TJ fix for a while!

    The wire looks fab btw been wondering about it for a while so thanks for this video!

    XX

    ReplyDelete
  5. cisco99044 February 2013 at 20:33

    Yes Todd everyone here in the USA loves this wire.I will be getting some here to team if you would like me send you some if it is a different size I would have no problem. From: Randy Blankenship here in the USA

    ReplyDelete
  6. Unknown5 February 2013 at 00:09

    am I the only one thinking that by using this stuff you would have to trade off over draw length?

    because of the increased surface area the juice will be vaporised quicker than it would with normal round wire, and this introduces a possibility that the wicking process can't keep up with demand by the coil?

    or am I just over thinking things?

    ReplyDelete
    Replies
    1. Unknown5 February 2013 at 12:59

      Was thinking the same, you would need to be very sure of the wicking quality of your wick or cut back on the chain vaping lol

      Delete
    2. Dave H5 February 2013 at 14:48

      Wonder in the Ebay seller is noticing a increase in sales! When I ordered mine it said they'd sold 150 odd, now it's at 194, I bet they don't normally sell nearly 50 in a day! lol

      How do you think this would work with silica wick?

      Delete
    3. Todd5 February 2013 at 14:49

      Would imagine it'll work fine Dave, going to try some in the Kayfun later on :)

      Delete
  7. Baz6 February 2013 at 08:56

    Ive tried the 0.5 & 0.6 now, definitely dont need so many wraps on the 0.5, 4 wraps is at 1.3ohm, but I usually vape between 1.1 and 1.5ohm

    ReplyDelete
  8. Unknown8 February 2013 at 13:12

    Just got some of this,great on u wick aga t in fact fantastic!!

    ReplyDelete
  9. Neofolis28 February 2013 at 11:21

    Hi Todd, you should give lower res a try. I know taste is subjective, etc., but I usually go with 4 wraps on a 2ml wick, which comes out at 0.8ohm and it's great. Obviously I have to stick with mechanical mods and theoretically the battery drains faster, but the coil heats up much faster, so you tend to take shorter drags, which compensates to a large extent for the faster drain. I still get a good day out of an Aw IMR 18650 2000mah. I can't go back to higher res coils now, I find them tedious, because they take too long to heat up.

    ReplyDelete
  10. Todd28 February 2013 at 11:35

    1.1 - 2 is my sweet spot so I'll stick with that, suits me to a T :D

    All the best Boyo

    Todd

    ReplyDelete
  11. Unknown28 March 2013 at 04:02

    Todd you can get the wire in the UK from www.themeshcompany.com they only carry 1 type though well at the moment and that is 0.5 X 0.1 mm. slightly higher resistance to the stuff you were using.
    If this info has already been post sorreeeeeeee
    alan

    ReplyDelete
  12. Unknown28 March 2013 at 14:38

    Hi me again well coiled up a MAGA with this 6 wraps 1.7ohms got my kick turned all the way down and its flying lol no hotspots with it at all. I used the drill bit method for coil. hope this info is helpful

    cheers
    Alan

    ReplyDelete
    Replies
    1. Todd28 March 2013 at 15:09

      Peoples feed back is always useful mate, glad it's working well for you :)

      Delete
    2. Unknown28 March 2013 at 16:57

      opps 7 wraps lol

      Delete
  13. Flats for sale in hitech city14 June 2013 at 23:37

    Wonderful information, I had come to know about your blog from my friend nandu , hyderabad,i have read at least 7 posts of yours by now, and let me tell you, your website gives the best and the most interesting information. This is just the kind of information that i had been looking for, i'm already your rss reader now and i would regularly watch out for the new posts, once again hats off to you! Thanks a ton once again, Regards,

    ReplyDelete

Post a Comment